<![CDATA[CANNY logic forum — CANNY 5.3 pico / MD1A]]> 2025-07-30T12:57:07Z PunBB https://forum.cannylogic.com/index.php <![CDATA[Sending ADC Value to CAN]]> Hi I am trying to send an ADC value to CAN but I am having trouble even connecting to the bus.

I have the program "FuelPumpPrime+Scramble2.3" working on a different bus at 100k bit/s.

However when I try to use the same method to connect to a 500k bit/s bus, I don't seem to get any data. I have uploaded the ccm firmware to the device and I can connect and read the bus at 500k bit/s. But when I put a test value of 0 for Y under Engine_Run_Only_Signal (Oil_Press+Engine_Run_Signal+CAN_Broadcast), the output does not trigger. I don't seem to be receiving can data.

I'm also not sure if the pic5.3 is transmitting any data.

Output 8 also doesn't seem to be doing what it should. With no input from ADC, the output should be grounded but it seems to float.

I have confirmed CAN terminations and do not need any; there is 60ohms resistance on the bus wiring and the point I am tapping is where I had removed an auto trans control modules so I know it was not EOL.

]]> https://forum.cannylogic.com/profile.php?id=340 2025-07-30T12:57:07Z https://forum.cannylogic.com/viewtopic.php?id=92&action=new <![CDATA[5.3 MD1A start parameters]]> Hello! Can someone guide me how to get started with setting up the MD1A to get 5v from channel 8? I am using 12v input voltage and also intend to read the voltages 0-5v on channels 9 and 10, which I have jumpered to the appropriate adc contacts on the unit. Any assistance with the registers is very appreciated!

]]> https://forum.cannylogic.com/profile.php?id=339 2025-06-30T21:44:25Z https://forum.cannylogic.com/viewtopic.php?id=90&action=new <![CDATA[3d Model]]> Hello

Do you have a 3D model of the PICO 5.3 Module?

Stephane.

]]> https://forum.cannylogic.com/profile.php?id=259 2022-08-07T15:56:16Z https://forum.cannylogic.com/viewtopic.php?id=63&action=new <![CDATA[Type and Reference of the connector]]> Hello

Can you please confirm the type of connector used?

Is this PHDR-08VS for the cable?

Thanks

]]> https://forum.cannylogic.com/profile.php?id=259 2022-06-12T10:51:11Z https://forum.cannylogic.com/viewtopic.php?id=61&action=new <![CDATA[How to create SFX without a diagram and even a firmware?]]> Hello

I need to be able to create an SFX to allow users to update the User Parameters BUT I do not want to provide the diagram as it could be stolen to replicate the modules. The firmware is not even needed in this use case.

Thank for any help!

]]> https://forum.cannylogic.com/profile.php?id=259 2022-06-07T15:48:18Z https://forum.cannylogic.com/viewtopic.php?id=60&action=new <![CDATA[Canny Data Transfer]]> Hi

My old canny module messed up and i got a replacement canny, but how do you transfer the data from the old one to the new one.

Cannylab doesn't have reading data feature or am i missing something.

thanks

]]> https://forum.cannylogic.com/profile.php?id=295 2021-12-04T12:43:45Z https://forum.cannylogic.com/viewtopic.php?id=48&action=new <![CDATA[Canny 5.3 pico - Termination resistor]]> Hello

Where is the location of the termination resistor?

Stephane.

]]> https://forum.cannylogic.com/profile.php?id=259 2020-01-04T13:11:26Z https://forum.cannylogic.com/viewtopic.php?id=28&action=new